Digiprog 3 mileage correction tool what works & not work

Here is a list of Digiprog 3 V4.94 odometer correction tool master programmer customer feedback on what works and does not work.

This list will keep updating.

Part1: VW
VW tuareg 2003 OBD OK 
2008 VW Jetta OBD good
2011 Golf VI Dash via OBD + DSG reset – OK
VW golf 5 2003 OBD no connection
VW golf 5 2008 OBD OK
VW golf 4 2002 bosch OBD OK
VW golf 4 2004 tdi OBD OK
VW eos 2008 OBD OK
VW polo bluemotion diesel 2011 OBD OK (only with 4.88!)
VW golf 6 2010 OBD OK
VW passat 2002 via OBD OK
VW Golf mk5 2006 dash+ edc16 OBD is good
VW Golf mk6 2009 OBD is good with error clearing
VW sharan OBD –not working
2000 Passat B5 OBD – OK
Touareg 2 2011 new dash ARB 8 - not OK!!
Touareg 2 2011 Disel(chip 95320) - not OK!!
Passat B6 2006 from the first test panel may be turned off. then when the ignition is switched on again and try to second time.
Jetta 2012 Nec+24c64 ( choose AmarOK)
VW caddy 2009 1.9 bls OBD2 OK
VW transporter 2011 OBD OK
VW t5 2004 bensin odb OK
VW caddy 2013 obbd not OK
VW Passat new shape december 2012 OBD could not get mileage under 110k
2012 VW polo OBD- no good -> need v4.88
VW golf 5 2007 OBD tacho OK, ecu OBD OK
volkswagen up 2013. OBD no connection
VW transporter T5 2009 ecu edc16 diag NOT OK
VW Golf IV OBD2 – OK
VW Golf 5/6 OBD – OK
VW Touran 2006/2007 OBD – OK
VW transporter 2014 OBD – OK (v4.94)
VW passat 2006 dash OBD – OK
VW passat 2006 dsg OBD – OK (reset to 0)
VW passat 2006 ecu OBD – not OK (10min)
08 VW t5 OBD 1 min – OK
VW Passat"99 OBD – OK
VW Passat "03 OBD – OK
VW polo 2002 1.4tdi, OBD – OK
VW Caddy 2013 OBD – OK
VW Tiguan 2009 OBD – OK
VW Turan 2003 OBD dash & edc – OK
VW Golf 6 OBD – OK
VW Golf 4 OBD – OK
VW Passat B7 1.4 TSI EcoFuel 10.2011 - All is OK by OBD 4.94
VW turan 2009-2011 OBD – OK
2009 golf 6 convertible OBD – OK
2013 VW t5 OBD – OK
caddy 2007 dash and ecu OBD – OK
Golf 6 2012 done by OBD – OK
Caddy 2013 done by OBD– OK
VW touareq V10 2005 OBD – OK
Passat B5 - OBD – OK

Part2: Ford
2001 Ford F150 HC11 MCU No Good Destroyed Dash118
2003 Ford Focus OBD Good
ford fiesta 2011 OBD OK
Ford Focus 2009 OBD is good
Ford Mondeo 2009 OBD is good
Mondeo 2010 with color screen, not OK!
Focus 06y by OBD OK
galaxy 01y such as sharan by OBD OK
old galaxy before 2000y by OBD OK
Ford Mondeo 2008 2.0tdci - OBD2 OK
Ford Focus 24c16 in circuit with adapter ST47 works good
Ford Fiesta 2009 OBD-No Good Obp - No Good
Ford Focus 2008 OBD-Good
ford focus 2006 OBD OK
ford fiesta 2002 (2003 model) OBD –not OK
Ford Focus 2007 Dashboard HCS12 - done OK
Ford Mondeo MK2 Dashboard HC12 - done OK
Ford C max 2004OBD – not work
Ford Focus 2001 – OK
Ford Mondeo 2002 – OK
Ford Kuga 2012 - OBD OK (4.88)
Ford Focus MY 2010 1.6 Petrol (SIDA engine) - OBD OK

Part3: Audi
Audi A4 2002 OBD, OK
2008 Q7 Audi OBD no good "No Connection"
2012 Audi A4 2.0tdi Dash via OBD - OK
2013 Audi Q5 2.0tdi Dash via OBD - OK
Audi a4 2005 OBD OK
Audi a4 2009 OBD OK
Audi tt 2009 roadster diesel OBD OK
Audi A6 '99 via OBD – OK
Audi A6, 2004, via OBD, OK
Audi A3 2008 OBD is working
A4 2006(M73) not reading old mileage, but writing new
Audi a4 2010 2.0tdi OBD OK
Audi a5 2011 2.0tfsi OBD not OK
AudiS3 2004 OBD - OK
Audi R8 '09 via OBD – OK
Audi A6 '03 via OBD – OK
Audi a4 2010 OBD OK
Audi tt 2009 convertible diesel! OBD OK
Audi A6 2008 - OBD Good
Audi A5 2011 - OBD No Good
Audi A5 2011 programme by chip – Good
A4 2008 work OK 25 min
A3 2004 work OK 5 min
Audi A4 B8 model 2010 - OBD OK
Audi A5 2012 - OBD OK
Audi A6"97-via chip-OK
Audi Q5 - 2010 Works OK OBD 10 min
Audi q7 instrument by OBD - OK
Audi A4 2001, 2003 OBD - OK
Audi A6 2.0tsi 2005 OK by OBD(with two hits).
Audi A4 1.8 turbo 2004 OK by OBD
Audi A4 2.0 petrol, 96kw, 2001 year it says UNKNOWN RB4 DASH
2006 Audi a4 - OBD – OK
2011 A1 sline petrol OBD OK

Part4: BMW
1999 E46 BMW Dash+LCM OBD Good
BMW 5-serie 2000, LCM OBD OK, tacho OBD not OK
2005 E46 eeprom – OK
BMW E46 LCM on OBD is good
BMW E46 1999 dash/lcm/service>OBD OK
CAS3 just read mileage
e60 dash chip 35080 just reding, not erasing. need new chip
E46 dash chip 35080 just reding, not erasing. need new chip

Part5: Mercedes
1999 E55 Merc OBD Good
Mercedes c202 38 pin OK
Mercedes e211 2004 tacho and ezs OK
Mercedes E 1999 38pin OK
Mercedes e- klasse (w211) 2004 OBD OK (+DPF diag OK)
Mercedes W204 2009.2010.2011
e-klasa 97y by 38 pin OK
Mercedes W140 1993 cable 11 work OK
v4.85, Mercedes w212 2010,dash+ezs OBD work OK
2012 MB E350 OBD -OK
Merc W211 2003/2005/2007 OBD - OK
Merc W203 2004 OBD - OK
Merc W209 2004 cluster plug - OK
Mb W204 2008 Ezs + Dash - OBD OK
Mb W169 Dash by Adapter - Not OK ( Think Adapter not good )
SLK 2012 worka OK 5 min in EZS km 
vito 2001 OBD OK 
Mercedes A - W168, 2003 year - OBD OK
Mercedes S Class W221 ---> AMG S65 Eeprom file write 24C08 work Perfect
Mercedes ML 2004 - OBD - OK

Part5: Skoda
2009 Octavia FL 1.9tdi Dash + ECU via OBD - OK
2009 Fabia II 1.4tdi Dash via OBD - OK
skoda Fabia 2000 OBD OK
Skoda Octavia 2009 1.9 tdi bls - OBD2 OK!
Skoda Fabia 2004 OBD2- OK
skoda yeti 2012 digi4,82 OBD menu 32/64 OK
Fabia 2007 OBD -OK
Skoda Octavia 2012 OBD OK
octavia 2009 dash and ecu OBD OK

2010 Roomster 1.6tdi Dash via OBD - OK
2008 Roomster 1.9tdi Dash via OBD - OK

Part6: Opel
2001 Opel Vectra 1.6benz Dash via Chip - OK
opel astra 2001 OBD not OK, eeprom OK
opel corsa 2001 OBD OK
Astra '99 via OBD - OK
Vauxhall/Opel Astra J 2011 OBD is good.
But same Astra 2010 has access denied
Opel Vauxhall Vectra 93c66 unable to read
Opel Insignia '09 via OBD - not OK (acces denied), via chip - OK
Opel Astra 1999 OBD2 - OK
Opel astra 2000 OBD OK
Opel Zafira 2001 OBD OK
Vectra B OBD OK (1998)
OPEL Combo"06 OBD-OK
Opel Vectra"98 OBD-OK
Opel Vivaro2006- chip-OK
Opel Astra J 2011 - OBD - OK
Astra h 2005 dtl - OBD not work
Opel Corsa D 2009, 2010 by chip programing - OK 
Opel Vectra C - OK
Opel Meriva 2007 OBD - OK
Corsa C 1.3cdti - OBD OK
Zafira A - OBD OK
Opel Corsa C - OBD - OK
Opel Astra H - chip 35080 - OK
Opel Meriva - OBD - OK

Part7: Peugeot
2002 Peugeot 607 BSI via chip - deleted?! Dash read 0km - not OK
Peugeot Boxer 2010>OBD OK
""""""""""" Boxer 2007>OBD OK
PEUGEOT 307 BSI 95160 in circuit adapter ST47 works good
Peugeot 206+ '10. via chip (BSI and tacho) - OK
Peugeot 308 '11. via chip (BSI and tacho) – OK

fiat ducato 2007 OBD OK
fiat ducato 2012 OBD not OK
fiat 500 2010 OBD OK
fiat punto evo diesel 2010 OBD not OK
fiat doblo 2005 OBD OK
Fiat Panda '09. via OBD - OK
Fiat Grande Punto '09. via chip - OK
fiat ducato 2014 - OBD OK
fiat 2014 (december). was OBD OK

Part9: Others
chrysler voyager 2001 OBD not OK
Chrysler 300C 2013 OBD - NOT OK
dodge nitro 2007 OBD OK
chrysler 300c 2009 - OBD
2006 Chrysler 300c - OBD- OK 

volvo xc60 2008 OBD OK
v70 -2011 is possible (OBD)
xc60 -2012 is possible (OBD)

Mini R56 via Eeprom - OK 

Toyota Avensis 2007 clip is good
New Toyota Avensis 2009> clip is good

2012 Commodore eeprom - OK
2008 Lancer eeprom - OK
2011 Falcon eeprom - OK

honda legend 1999 2x eeprom OK
Honda Civic 2007 - Eeprom 93C76 Chip - OK
Honda Civic '03. via chip - OK (difference in km on tacho and Digiprog3 over 150km)
Honda Jazz 1.2, 2002 - by chip OK
2007 Civic type R fn2 success via chip

seat ibiza 2013 OBD not OK
seat ibiza 2011 OBD OK
Seat Leon 1P 2006 - OBD OK
Seat Ibiza"99 OBD-OK
Seat ibiza"01-OBD-OK
Seat Ibiza 2001 1.6 petrol OK
Seat Ibiza 2012 OBD OK
Seat Leon OBD - OK
Seat ibiza 2001 - done by OBD

porsche boxter 2008 OBD OK

Mazda 6 - 2009 93c66 desoldered - dump crashed

Alfa 147 Dash E2p – OK

Citroen Saxo 2002-cable ST43-OK

citeoen c4 grand picasso 2008 bsi and dash-done by chip
Citroen c5 bsi via chip done
Citroen C3 - chip BSI (95160) & Dash (93C46) - OK 
Citroen C5 2011 Bsi+dash - OK

Laguna II ph1 - OK
Laguna II ph2 - OK
Megane II 2004 - chip 93C56 (Visteon) - OK 

Hyundai coupe -via chip-OK
Hyundai Tucson 2005 done by chip


Dodge Ram 1500 HCS12 Pinout to Digiprog 3

Here is the pinout intuction to Dodge Ram 1500 HCS12 cluster if you need to change mileage on this model by digiprog 3 v4.94 odometer correction tool.


The digiprog3 pinout here is for Ram with HCS12 cluster, if your Dodge have differnt instrument cluster inside as picture below. You cannot follow the pinout.

Dodge Ram 1500 HCS12 Pinout to Digiprog 3 pic 1

Dodge Ram 1500 HCS12 Pinout to Digiprog 3 pic2
Note Tacho Meter
Dismantle Tacho meter

Identify processor
Solder the colored cables of Plus 51 to the suitable points

Connect Digiprog to separate electricity supply 
Urgently necessarily 
Connect digiprog with the plug

Follow the instructions of the digiprog

Choose program: PKW/LKW-Dodge-Ram--HCS12

Follow DigiProg prompt until mileage is successfully changed.

Digiprog 3 Pinout to Dodge Ram 1500 with ST92F120 MCU will be available in feature post.


Will Digiprog 3 change mileage on Mercedes W212?

I want to correct mileage on my W212 2013 year. Is only way to use MB CAN Filter?  I found some tutorial in carprog but doesn’t show steps with the mileage adjust. For example, if install mb can filter, do you still update ezs odometer value or just cluster? Yes I know AVDI Abrites original does it all, before you tell me, but can’t afford that software yet.
Anywhere else have to change it? Tire pressure sensors of transmission?
Thank you in advance.

Customer solutions:
1.Late 2013 Mercedes W212 you need to correct odometer and install CAN Filter (EZS nothing).The can filter goes near the cluster. I have done with Yanhua Digimaster 3. It is not cheap. But I think at you can use digiprog 3. By the way, take backup from eeprom first.

2. If it is full color dashboard, digiprog 3 cant do it..
If it’s not facelift model (so before 2013) and use digiprog 3 v4.94, then you don’t need can filter/blocker.
But a can blocker is better to use all times, because if dealer reads the EZS it shows same mileage as in tacho, if you dont use can blocker then EZS shows 999999km.. (but normally dealers don’t read EZS, they only read ‘assyst manager’ when serviced).
To change mileage you need to use option ‘EZS’ in menu of mercedes w212 of digiprog III.. then it blocks ezs and changes tacho automatically.
If you roll back odometer to a lower mileage off last service, its best to delete service history in car. use option ‘assyst manager’. enter ‘744’ days and ‘25000’kms for next service warning, and press ‘V’ when it asks to delete service history.
When you have a diesel it probably gives DPF error in car. and the car will run in emergency-mode, only drives max 80kmh. digiprog can’t reset this. You have to go to dealer or someone else who can reset dpf.
When some other errors turn up in display use the ‘clr error’ option to reset.


Nissan Navara PDF BDM to Digiprog 3 ST48

Can someone help me to get PDF for this pickup Nissan Navara year is October 2013 and inside is 9S12 processor, i have Digiprog 3 odometer correction master but no pdf i send foto.
Nissan Navara cluster 1
Nissan Navara cluster 2

photos too fuzzy.
this is what I have for connections Nissan Navara 2014
connections Nissan Navara 2014
these are the points of connection for digiprog 3 v 4.88
using cable 48
greetings reports.
cable 48
in menu digiprog go to nissan navara 9s12

ST48 colors and pinout and tips on 9s12 processors. Find the ground at it should be easy to figure out if it has the 6 pads or 6 pins.
ST48 pinout

Almost all clusters with 9s12 Processors have this setup, a quick way to program almost any digital odometer with a 9s12 processor.

I have had good success using ST48 and the MCU function from Eeprom menu of Digiprog3.  See example picture, a lot of times the two unused pads have no solder bump on them, a clue to the orientation.  Sometimes access is from the other side of the board and the contact points would be reversed like below.
Reversed contact point layout
Reversed contact point layout 
9s12 Processors pinout


Digiprog 3 V4.94 read Audi A4 eeprom HC12 in cluster

copy the immo information from a cluster to another
make the mileage follow with the immo information
If clone all eeprom content than the mileage is transferred too.

Audi a4 2001

Optional devices:
Digiprog3, or ecu programmers like XprogCarprogUPA USB programmer

Original cluster:
The Jaeger cluster barely works
Original cluster 1
Original cluster 2
Original cluster 3

read the pin code from both the Instrument and adapt it to the vehicle

What to do on pin 21 and 22 on the chip:

pin 21 and 22

– With car ECU programmers:
Eprom.set type,mcu,hc12,read,save.
eprom,set type,mcu,hc12,file,load,write.
Buy yourself Xprog-M programmer, Carprog full, UPA USB.
Pin 21 and 22 jumper after programming or wait 10 minutes.

– with Digiprog 3:

Eprom,set type,mcu,hc12,read,save.
eprom,set type,mcu,hc12,file,load,write.

Eeprom HC12 read and write to the other counter:

(Write down the exact ALWAYS old / incorrect Mileage)
The diagnostic port is in the driver’s footwell. Turn the ignition
on a vehicle. Connect plug ST16 the diagnostic port and the

Select the program: cars / trucks – AUDI – MM 4 / 99- DIAG.
The DIGI PROG II shows you the old / incorrect Mileage.
Enter the new / correct Mileage and confirm this.
Should be then after programming on the speedometer 999999 KM give
The old / wrong KM value again so that the speedometer again the old /
false indicates KM. Now you build the speedometer and break it to the
see board. Solder the green and black wire to the same color marked
Arrows at. Now connect the blue and the green plug with
the speedometer and plug ST41 with the DIGI PROG (picture on the following page.)
Now select the program: cars / trucks – AUDI – MM 4/99 HC12.
The DIGI PROG shows you the old / incorrect Mileage. Enter the
new / correct Mileage and confirm this with the hook.
Now shows you the DigiProg II 5 min wait. Remove the connection
between the DigiProg and the speedometer, wait 5 minutes and build the speedometer
again. Alternatively, for 5 min. Wait, you can also like in the image on the
next page shows the pins 21 and 22 bridges.
shows the pins 21 and 22 bridges
Here necessarily the board from any power supply (Digiprog3 v4.94,
external power supply, etc.), Pin 21 + 22 bridge, and then you can use the tachometer
Immediately reinstall.
Pin 21 + 22 bridge

OBD365 disclaimer:
Thanks for all tech support from members’ share at cartechnology forum.


Ford Expedition 2003 mileage change with Digiprog 3

Has anyone used the Digiprog 3 v4.94 on a 2003 Ford Expedition? I'm not sure what cable to use or the correct connection points.


Several boards were in those clusters Digiprog iii will work most of them were hc912 mcus.
Digiprog will do them whether your writing them manually by hand or with another calc built into digi
if its a hc11 it will also work

Ford Expedition 2013 dash pictures attached:


 the processor in that board is a hc912d60 mcu board

and according to tachosoft these are the mileage blocks

Car type: Ford Expedition - 68HC912D60 - 2003 year
The mileage is stored in the next lines:
0340: 4A 38 xx xx xx xx xx xx xx xx xx xx xx xx xx xx
0350: 4A 38 xx xx xx xx xx xx xx xx xx xx xx xx xx xx
0360: 4A 38 xx xx xx xx xx xx xx xx xx xx xx xx xx xx
0370: 4A 38 xx xx xx xx xx xx xx xx xx xx xx xx xx xx
0380: 4A 38 xx xx xx xx xx xx xx xx xx xx xx xx xx xx
where the next bytes:
4A 38 - is a mileage

Try this connection.

yes thats what you needed for wiring under digiprog3
goto eeprom
then page down to mcu
then select 9s12 and 9s12 4k
i believe its the 4k you need for d60
use ST48 which is 5volt St51 is 12volt when powering board instead of just mcu

wire how clusters pic is which is your life saver knowing where to grab reset on board
then handwrite mileage block

or make your life alot easier and order a usaprog or datasmart dsp3 something else
but digiprog will do as well.

Can digiprog 3 change mileage on BMW F10?

I will buy an 2012 f10 BMW and i would like to know if its possible to change the mileage on it with my digiprog 3 v4.94 odometer master?

Actually for me it would be enough if only the dash and maybe the cas would show the mileage, the rest i don't care for the time the car will be mine. 

I have not seen the car on the digiprog list? But i have seen it on the digimaster 3 list with something online? Can someone explain it to me how it would work?

It is impossible to do this dash via obd. you need special programmer (i.e digimaster iii) to erase the chip before writing new km, if it don't work, then have to replace chip

Digiprog3 will do miles in dash if you have a tool to erase 35160 first as for cas you will need good tool it will have 5m48h micro or you can put blocker in cluster.

digiprog3 v4.94 vehicle list


Digiprog 3 v4.94 “Disk index out of bounds” error solution

Here is the solution on how to solve Digiprog 3 v4.94 Odometer correction Master update software “Disk index out of bounds”.


digiprog 3 Disk index out of bounds
Digiloader1.exe: Disk index out of bounds

Possible reasons:
1- WinXP is not compatible with the digiprog3 4.94 update software
2- Digiloader1 file was killed by virus
3- The update file is not complete

Useful tips:
Try to use Windows XP operating system below:
1- operating system here is only for digiprog 3 at obdii365.com
2- disable anti-virus program, otherwise, the Digiloader file would be killed by virus.


Digiprog 3 V4.94 change mileage for Chevrolet Trailblazer

Here is the customer solution to Chevrolet Trailblazer 2002 KM change with Digiprog 3 v4.94 odometer correction tool.
Many thanks to a well-known member in GMT nation forum who achieved this.
Digiprog3 and ST 01/2 cable used is China clone.
The entire kit cost $169, with a set of cables and adapters. But i don’t think everyone should buy the entire kit, for the main unit should come with ST01, ST04 cables, which will save $40. Of course you should use st01/ st04 or have other adapters in hand.

And the model to chang mileage:
Chevrolet Trailblazer LTZ 2002

And here is some useful pictures for the same process:
And here is the final result
Before mileage correction
After mileage correction with Digiprog3 V4.94
And here is some notes for doing this properly :-
  • For US users, please make sure to check the Voltage of the adapter before connecting to AC (use the one included with the unit as it’s 110-220 V ). Just to make sure you don’t fry your Digiprog iii programmer
  • Also for US users, Change the netric unit from KM to MPG or Vise Versa from MPG to KM; for European users, before reading or Writing on the Chip
  • Very Very important to connect the programmer clip as per the pictures attached where the Red Color pin in the Clip is Up (See the picture above)
  • Before assembling the cluster back together connect it to the car first and check the mileage reading before installing needles back and installing the whole cluster back to the car
  • Also Very Very Very Important that you always save the old chip data in the DP3 programmer for any thing goes wrong so you can write it back if needed or even if someone fried his chip and needed to install new chip it will be really easy to write it back
  • if you needed any time to restart again or your Digiprog got stuck while working simply take out the Power plug and reinsert it again to restart the programmer (Never ever unplug AC power Plug when odometer correction tool is reading or Writing on the EEPROM CHIP otherwise you will destroy it)

If you are interested, check the small video operation he made here.