6/01/2018

Digiprog 3 Ford Odometer Correction: Yes and No

Here, obdii365.com has collected almost Digiprog 3 Ford test/feedback on the web. Have listred Ford models that Digiprog 3 odometer correction tool support and doesn’t support.


Look here:
Digiprog 3 on Ford: success
Digiprog 3 on Ford: failed
Digiprog 3 Ford Vehicle List

(Note that here all DP3 refers to the china clone)

Digiprog 3 on Ford: success!

Ford Focus 2005: (Model 2004>) OBD OK

Ford Transit: Just done a merc 204 and 212 Diagnostic mileage and assyst

Ford Focus 2008 to 2011 Diag
Ford Fiesta 2008 up Diag
Ford Mondeo 2008 Diag
Ford Focus diag

Ford C-Max and S-Max: work OK via OBD
Ford Fiesta & Focus: works OK via MCU, not Dash Connector ?!?!

Ford smax: work fine and i think with Fords work fine

Ford focus: 2007 ok

2011 Ford focus: works like a dream obd2

Ford focus 2010: OK

Ford escape 2008: OBD ok

Ford fokus 2002,read old km—-not write new km

Ford ranger 68hc05: ok

Ford transit 93c76 eeprom: ok

Ford fusion hc 12 plug: ok

Ford mondeo 2008: obd ok

Ford focus hc11: ok with plug

Ford focus 2006: obd ok
Ford focus 2004-2010: obd ok

Ford s-max 2009: obd ok
Ford Fiesta 2012: OBD OK (fiesta 2005 obd not ok)

Ford fiesta 2008-2010 red screen: obd ok

Ford Fiesta HCS12: ST48 Work

Ford Mondeo 2008: Full Colour Fis 24C16 – – – OBD diag Read – 0km,Write – OK!

Ford mondeo 2010: visteon dash with 9s12 read ok write ok via 4 wires on pcb

Ford mondeo 2004: st51 read ok/write ok

Ford Bantam 2006: need nec programmer

Ford connect 2008: obd not! fvdi obd, read km but not change! dp3 ,conector 48, 9S12read and write km!


Digiprog 3 on Ford: failed!

2006 Ford fusion: obd not work

Ford connect 2002 with 912 with cable 48/2 cluster: dead mcu not readable even with etl !!!

Ford Fiesta 2002: via obd not work

Ford F150 2002 with HC11: N O N E S !!!! wasted time… Not working… After try connection show E R R O R !!!
F150 2002: i have do 2 weeks ago with digiprog 3 clone and works fine. have you make wrong job

Ford Escape 2007: no work obd2, cable 16
error unknown dashboard

Ford fokus 2002,read old km—-not write new km

Cable Ford focus not ok.
Check with scheme or compare with other programmer.

2006 Ford fusion: obd not work


Digiprog III Ford Car List:

Ford C-MAX ,S12
Ford EXPLORER S12
Ford FIESTA (-2009)
Ford FOCUS 2004- s12,s12x
Ford FUSION S12
Ford MAVERICK/EXPLORER 2007-
Ford MONDEO 2008-,SMAX,GALAXY 2006-
Ford MUSTANG (7R33)
Ford Smax/Mondeo/Galaxy s

Ford Bantam
Ford Calaxy -2006
Ford Calaxy 2006-
Ford Cmax
Ford Connect
Ford Connect Programming Via Micro
Ford Cougar Cluster-Diagnosis
Ford Edge
Ford Escape 2007-
Ford Escape Hybrid HCS12
Ford Explorer
Ford Explorer 2003 Programming Via Micro
Ford Explorer Programming Via Micro
Ford F-Series
Ford F150 2004 Programming Via Micro
Ford F150 HC11 Programming Via Micro
Ford F150 HCS12
Ford F250
Ford F250 HC12 Programming Via Micro
Ford F350 Program Via Cluster
Ford F450
Ford Feista 2003
Ford Feista 9S12 2006 model Programming Via BDM
Ford Fiesta 2001-2008
Ford Fiesta 2008 hcs12
Ford Fiesta 2008-
Ford Fiesta 2009
Ford Fiesta Cluster-Diagnosis
Ford Fiesta KA
Ford Figo
Ford Focus 2003 Chp & Micro all models Programmin Via chip Or BDM Points
Ford Focus 2004-
Ford Focus 2008
Ford Focus Cluster-Diagnosis
Ford Focus/Cmax
Ford Freestar
Ford Fusion
Ford Fusion Progarmming Via Chip
Ford GT 24c08
Ford Galaxy 2000/2006 Diagnosis
Ford Galaxy Diagnosis
Ford Kuga
Ford Maverick 2007-
Ford Maverick HC11 Programming Via Micro
Ford Mondeo 2008-
Ford Mondeo Cluster-Diagnosis
Ford Mondeo/Galaxy/Smax
Ford Mustang
Ford Mustang
Ford Mustang 2007-
Ford Mustang 24C32
Ford Mustang Programming Via Micro
Ford Puma Cluster-Diagnosis
Ford Ranger 2007
Ford Ranger 24C16
Ford Ranger Programming Via Cluster
Ford SMAX
Ford Scorpio Cluster-Diagnosis
Ford Smax
Ford Tarus 2003/ Only in our office
Ford Territory
Ford Thunderbird 2005/ 2006 model Programming Via BDM
Ford Thunderbird HC11
Ford Transit
Ford Transit 2003
Ford Transit 2004 Programming Via Micro
Ford Transit Model 2003
Ford Transit TVI Chip 66 Progarmming Via Chip
Ford VAN F150
Ford Windstar HC11 Programming Via Micro
Ford s

5/20/2018

Digiprog 3 Changes Mileages on Smart ForTwo 2002 with EEPROM C66

Purpose: Change the mileage of a Smart Fortwo 2002 via an OBDII cable
Car: Smart ForTwo CM01 – year 2002
smart-fortwo-1
smart-fortwo-2
Odometer correction tool: Digiprog 3 Chinese version
Method: ODB2
Issues:
Digiprog 3 says “NO CONNECTION”.


Suggestion & Solutions:
2002 cannot be done via obd!!

First you have to reset the bcu and then correct the milage in the dash (its a eeprom C66).
Setting the eeprom worked fine.

Note 1: Wrong Pinouts
Sometimes Chinese cable schematics is wrong.

Note 2: What is BCU?
BCU= Bord Control Unit.
is under the steering wheel on the left side. (inside the reilais box). you have to dismount it and connect like in the manual. until now i couldnt find the right pinout for the Digiprog(im seraching). For me it worked only with “Tacho Pro”.
In the dash you can find two C66 eeproms you need the right one. You have to connect the red wire with the lower left leg of the eeprom (i couldnt connect it with the clip it worked only by soldering every single wire).
Here is the manual:

Requires plug ST01
digiprog-plug-st01-1
digiprog-plug-st01-2
SMART TACHO CHIP:
Remove the instrument cluster disassemble it.
Find the chip 93CS66.
digiprog-smart-fortwo-1
Put plug ST01 on the chip (read red wire on pin 1 writing from chip then bottom left is pin 1).
Select the program: Car / Truck – SMART C66.
digiprog-smart-fortwo-2
The DIGIPROG 3 v4.94 will show you the current / incorrect KM status.
Enter the new / correct KM-Stand.
FINISHED.


3/08/2018

Digiprog 3 V4.94 change KM on Toyota Hilux and Isuzu DMAX

Digiprog III v4.94 odometer correction tool master new test feedback: change odometer on Toyota Hilux & Isuzu D-MAX successfully.


Picture guide attached below:

Digiprog3 v4.94 change KM on Toyota Hilux 93C66
digiprog-3-toyota-hilux-1
digiprog-3-toyota-hilux-2
digiprog-3-toyota-hilux-3
digiprog-3-toyota-hilux-4
Digirpog 3 v4.94 change mileage on Isuzu D-Max
digiprog3-isuzu-dmax-1
digiprog3-isuzu-dmax-2
digiprog3-isuzu-dmax-3
digiprog3-isuzu-dmax-4

12/17/2017

How to use Digiprog 3 to change mileage on Audi A8 2003-

Digiprog 3 v4.94 odometer correction tool how to use for Audi A8 (2003-). Here are notes for you all, of Tacho meter value

Audi A8 (2003-)
audi-a3-2003
Diagnostic connection is located in the cabin
digiprog3-audi-a3-1
Connect Diagnosis Port with DP3 cable of Plug 16
digiprog3-audi-a3-2
Ignition on

Connect the DigiProg 3 main unit to Plug 16

The DigiProg needs no separate electricity supply; it is supplied via the diagnosis port

Follow DigiProg3 v4.94 instruction and change KM
digiprog3-audi-a3-3
digiprog3-audi-a3-4
Enter KM value and confirm Entry

Audi A8 mileage correction completed!

Before:
digiprog3-audi-a3-5
After:
digiprog3-audi-a3-6
Job’s done!

Note: If error message “Access denied” pops up, pls. choose:
PKW/LKW-Audi-A8-2003-(4E) 1. Flash Cxxx/
Dxxx
Confirm with Hook
Remove fuse 5 + 10
Wait approx. 5 seconds
Reinstall fuse
if tacho meter is dark
Switch Ignition on and off

Choose program:
PKW/LKW– Audi—A8-2003-(4E) Diag

Enter KM value and confirm Entry.

8/17/2017

How to change Volvo V60 odometer by Digiprog 3

It is possible to change change KM in Volvo V60 cluster. Depend of what tool you have. Here are instructions and pinouts provided.

VOLVO V60 HC12

volvo-v60-h12
Connector 51 is required
VOLVO V60 HC12
Remove the instrument cluster and remove the back cover.
Solder from connector 51 the colors at the marked same color
Soldering points. Disconnect the conductor (pink arrow)
(PICTURES ON THE FOLLOWING)
Connect the plug to the Digiprog 3 odometer correction tool.
Select the program:
Car / Truck – VOLVO V60 HC12.
The Digiprog 3 v4.94 shows the old / wrong CM reading.
The new / correct KM stand program and ready.
After confirmation, the process is completed.
Solder all connections.
FINISHED.
volvo-v60-h12-km-change-1
volvo-v60-h12-km-change-2

VOLVO V60 V70 S80 MOD. 2002 H12 V2

volvo-v60-v70-s80
Connector 51 is required
VOLVO V60 V70 S80 MODEL 2002 H12 V2
Remove the instrument cluster and remove the back cover.
Solder from connector 51 the colors at the marked same color
Soldering points.
Connect the plug to the Digiprog3 V4.94.
Select the program: Car / Truck – VOLVO V70 HC12 V2.
The Digiprog shows the old / wrong CM reading.
The new / correct KM stand program and ready.
After confirmation, the process is completed.
Solder all connections.
FINISHED.
volvo-v60-v70-s80-km-change-1
volvo-v60-v70-s80-km-change-2


blog.obdii365.com

7/27/2017

Yanhua Digimaster 3 and CKM100 adds Key Unlock and Reset

Original Yanhua Digimaster 3 odometer correction tool and CKM100 car key master key programmer released new upgrade on 27th, July 2017.

Digimaster III V1.8.1707.21 Update Feature (2017-7-27):
new add car models for odometer adjustment and airbag resetting models.
New added odometer adjustment:
1. American GM Buick Regal 24C32
2. American GM Buick LaCrosse 24C32
3. American GM Buick Verano 24C32
New added airbag resetting:
1. Luxgen 28556KM120

Digimaster/CKM100 New upgrade developed key unlock and reset functions. Free to all. (But require to work with DR key adapter)

Digimaster3/CKM100 Unlocking / Reset key data car models list
Car model PCB mainboard no./frequency/key No.
Audi PCB mainboard no:233.453.111-02
315MHz-8T0959754A
315MHz-8T0959754C
315MHz-8T0959754J
PCB mainboard no:233.453.111-05(06)
315MHz-4G0959754G
315MHz-4G0959754J
315MHz-4H0959754G
315MHz-4H0959754J
315MHz-8T0959754A
315MHz-8T0959754C
315MHz-8T0959754G
315MHz-8T0959754J
433MHz-8T0959754
868MHz-4G0959754K
868MHz-4H0959754K
868MHz-8T0959754D
PCB mainboard no:233.453.211-01(02)
315MHz-4G0959754J
315MHz-8H0959754DB
315MHz-8K0959754
315MHz-8K0959754C
315MHz-8K0959754G
PCB mainboard no:233.628.011-03
433MHz-7P6959754AF
868MHz-7P6959754L
PCB mainboard no:233.628.011-04
315MHz-7P6959754AR
433MHz-7P6959754AO
PCB mainboard no:233.628.021-02
868MHz-7P6959754AT
BMW    E series chassis    Aftermarket key
genuine key 315
genuine key 868
F series chassis
315MHz-5WK49663
315MHz-HUF5662
433MHz-5WK49662
433MHz-HUF5663
433MHz-HUF5767
868MHz-5WK49661
868MHz-HUF5661
Porsche
315MHz-7PP959753BM
433MHz-7PP959753AJ
433MHz-7PP959753BN
433MHz-7PP959753BQ
433MHz-7PP959753BS
Land Rover
315MHz-YWX000071
433MHz-5E0U40247
433MHz-YWX000061
Volvo
900MHz-5WK49266
Buick
315MHz-4 button-13500225/13584825
315MHz-5 button-13500224/13584825
Chevrolet
315MHz-4 button-13500222
315MHz-4 button-13500318/13584828
315MHz-5 button-13500221
315MHz-5 button-13500319/13584829
433MHz-2 button-13500218
Cadillac
315MHz-5 button-NBG009768T
GM
433MHz-3 button
433MHz-4 button
433MHz-5 button
Opel
433MHz-2 button-13149645
433MHz-2 button-13149658
433MHz-2 button-13188281
433MHz-2 button-13188284
433MHz-2 button-13500235
433MHz-3 button-13500234
Peugeot  Citroen    21676652
E25CI009
E28CI01B
E33CI002
Hyundai  KIA
CMFCH02
CMFEU03
HMFEU04
HMFKR04
HMFNA04
Mitsubishi
433MHz-G8D-644M
Renault
433MHz-285971998R
433MHz-285974100R
433MHz-285975779R
433MHz-805673071R
Dodge    Jeep   Chrysler    567.737.061
567.783.031
KOBOTO4A
M3N5WY72XX
M3N5WY783X
OHT692427AA
OHT692713AA

http://www.obdii365.com/info/yanhua-digimaster-3-update-to-v18170721-47497.html

1/18/2017

Honda Civic 2001 NEC Processor Odometer Correction

Question:
I need to change KM on a Honda Civic 2001 with NEC Processor. I'm looking for pinout to this model. I'm attaching pictures. I'm using Digiprog 3 v4.94 odometer correction tool to read not even sure if this programmer does this dash.



Solution:
Someone suggest using ST47 cable. It will not work.

ST47 is for eeproms, this dash is an NEC processor and Digiprog3 cannot do them.

Need a programmer capable of doing NEC, i.e the powerful mileage programmer-YanHua digimaster 3 III.


www.obdii365.com