Will Digiprog 3 change mileage on Mercedes W212?

I want to correct mileage on my W212 2013 year. Is only way to use MB CAN Filter?  I found some tutorial in carprog but doesn’t show steps with the mileage adjust. For example, if install mb can filter, do you still update ezs odometer value or just cluster? Yes I know AVDI Abrites original does it all, before you tell me, but can’t afford that software yet.

Anywhere else have to change it? Tire pressure sensors of transmission?

Thank you in advance.

Customer solutions:

1.Late 2013 Mercedes W212 you need to correct odometer and install CAN Filter (EZS nothing).The can filter goes near the cluster. I have done with Yanhua Digimaster 3. It is not cheap. But I think at you can use digiprog 3. By the way, take backup from eeprom first.

2. If it is full color dashboard, digiprog 3 cant do it..

If it’s not facelift model (so before 2013) and use digiprog 3 v4.94, then you don’t need can filter/blocker.
But a can blocker is better to use all times, because if dealer reads the EZS it shows same mileage as in tacho, if you dont use can blocker then EZS shows 999999km.. (but normally dealers don’t read EZS, they only read ‘assyst manager’ when serviced).

To change mileage you need to use option ‘EZS’ in menu of mercedes w212 of digiprog III.. then it blocks ezs and changes tacho automatically.

If you roll back odometer to a lower mileage off last service, its best to delete service history in car. use option ‘assyst manager’. enter ‘744’ days and ‘25000’kms for next service warning, and press ‘V’ when it asks to delete service history.

When you have a diesel it probably gives DPF error in car. and the car will run in emergency-mode, only drives max 80kmh. digiprog can’t reset this. You have to go to dealer or someone else who can reset dpf.

When some other errors turn up in display use the ‘clr error’ option to reset.

http://blog.obdii365.com/2016/09/14/which-tool-to-correct-odometer-on-mercedes-w212/

Nissan Navara PDF BDM to Digiprog 3 ST48

Can someone help me to get PDF for this pickup Nissan Navara year is October 2013 and inside is 9S12 processor, i have Digiprog 3 odometer correction master but no pdf i send foto.

photos too fuzzy.

this is what I have for connections Nissan Navara 2014

these are the points of connection for digiprog 3 v 4.88
using cable 48
greetings reports.

in menu digiprog go to nissan navara 9s12

ST48 colors and pinout and tips on 9s12 processors. Find the ground at it should be easy to figure out if it has the 6 pads or 6 pins.

Almost all clusters with 9s12 Processors have this setup, a quick way to program almost any digital odometer with a 9s12 processor.

I have had good success using ST48 and the MCU function from Eeprom menu of Digiprog3.  See example picture, a lot of times the two unused pads have no solder bump on them, a clue to the orientation.  Sometimes access is from the other side of the board and the contact points would be reversed like below.

Reversed contact point layout 

http://obd2expresscouk.bcz.com/2016/09/05/digiprog-3-pdf-bdm-for-nissan-navara-2013/

Digiprog 3 V4.94 read Audi A4 eeprom HC12 in cluster

Purpose:

copy the immo information from a cluster to another
make the mileage follow with the immo information

If clone all eeprom content than the mileage is transferred too.

Model:

Audi a4 2001

Optional devices:

Digiprog3, or ecu programmers like Xprog, Carprog, UPA USB programmer

Original cluster:

The Jaeger cluster barely works

Suggestion:

read the pin code from both the Instrument and adapt it to the vehicle

What to do on pin 21 and 22 on the chip:

– With car ECU programmers:

Eprom.set type,mcu,hc12,read,save.
eprom,set type,mcu,hc12,file,load,write.
Buy yourself Xprog-M programmer, Carprog full, UPA USB.
Pin 21 and 22 jumper after programming or wait 10 minutes.

– with Digiprog 3:

Eprom,set type,mcu,hc12,read,save.
eprom,set type,mcu,hc12,file,load,write.

Reference:

Eeprom HC12 read and write to the other counter:

AUDI MM AB 8/2001 DIAGNOSIS / TACHO DIAGNOSIS

(Write down the exact ALWAYS old / incorrect Mileage)

The diagnostic port is in the driver’s footwell. Turn the ignition

on a vehicle. Connect plug ST16 the diagnostic port and the

DIGIPROG.

Select the program: cars / trucks – AUDI – MM 4 / 99- DIAG.

The DIGI PROG II shows you the old / incorrect Mileage.

Enter the new / correct Mileage and confirm this.

Should be then after programming on the speedometer 999999 KM give

The old / wrong KM value again so that the speedometer again the old /

false indicates KM. Now you build the speedometer and break it to the

see board. Solder the green and black wire to the same color marked

Arrows at. Now connect the blue and the green plug with

the speedometer and plug ST41 with the DIGI PROG (picture on the following page.)

Now select the program: cars / trucks – AUDI – MM 4/99 HC12.

The DIGI PROG shows you the old / incorrect Mileage. Enter the

new / correct Mileage and confirm this with the hook.

Now shows you the DigiProg II 5 min wait. Remove the connection

between the DigiProg and the speedometer, wait 5 minutes and build the speedometer

again. Alternatively, for 5 min. Wait, you can also like in the image on the

next page shows the pins 21 and 22 bridges.

Here necessarily the board from any power supply (Digiprog3 v4.94,

external power supply, etc.), Pin 21 + 22 bridge, and then you can use the tachometer

Immediately reinstall.

OBD365 disclaimer:

TRY AT YOUR OWN RISK

Thanks for all tech support from members’ share at cartechnology forum.

http://blog.obd365.com/2016/08/29/digiprog3-xprog-carprog-read-audi-a4-eeprom-hc12/

Ford Expedition 2003 mileage change with Digiprog 3

Has anyone used the Digiprog 3 v4.94 on a 2003 Ford Expedition? I'm not sure what cable to use or the correct connection points.


Solution:

Several boards were in those clusters Digiprog iii will work most of them were hc912 mcus.
Digiprog will do them whether your writing them manually by hand or with another calc built into digi
if its a hc11 it will also work


Ford Expedition 2013 dash pictures attached:

 the processor in that board is a hc912d60 mcu board

and according to tachosoft these are the mileage blocks

Car type: Ford Expedition - 68HC912D60 - 2003 year
The mileage is stored in the next lines:
0340: 4A 38 xx xx xx xx xx xx xx xx xx xx xx xx xx xx
0350: 4A 38 xx xx xx xx xx xx xx xx xx xx xx xx xx xx
0360: 4A 38 xx xx xx xx xx xx xx xx xx xx xx xx xx xx
0370: 4A 38 xx xx xx xx xx xx xx xx xx xx xx xx xx xx
0380: 4A 38 xx xx xx xx xx xx xx xx xx xx xx xx xx xx
where the next bytes:
4A 38 - is a mileage

Try this connection.

yes thats what you needed for wiring under digiprog3
goto eeprom
then page down to mcu
then select 9s12 and 9s12 4k
i believe its the 4k you need for d60
use ST48 which is 5volt St51 is 12volt when powering board instead of just mcu

wire how clusters pic is which is your life saver knowing where to grab reset on board
then handwrite mileage block

or make your life alot easier and order a usaprog or datasmart dsp3 something else
but digiprog will do as well.

www.obdii365.com

Can digiprog 3 change mileage on BMW F10?

Question:

I will buy an 2012 f10 BMW and i would like to know if its possible to change the mileage on it with my digiprog 3 v4.94 odometer master?

Actually for me it would be enough if only the dash and maybe the cas would show the mileage, the rest i don't care for the time the car will be mine. 

I have not seen the car on the digiprog list? But i have seen it on the digimaster 3 list with something online? Can someone explain it to me how it would work?




Answer:
It is impossible to do this dash via obd. you need special programmer (i.e digimaster iii) to erase the chip before writing new km, if it don't work, then have to replace chip



Digiprog3 will do miles in dash if you have a tool to erase 35160 first as for cas you will need good tool it will have 5m48h micro or you can put blocker in cluster.

digiprog3 v4.94 vehicle list

http://www.obdii365.com/upload/pro/201501/v494-digiprog-3-vehicle-list-obd365.pdf

Digiprog 3 v4.94 “Disk index out of bounds” error solution

Here is the solution on how to solve Digiprog 3 v4.94 Odometer correction Master update software “Disk index out of bounds”.

Digiprog 3 v4.94 update software error message:

Digiloader1.exe: Disk index out of bounds

Possible reasons:

1- WinXP is not compatible with the digiprog3 4.94 update software

2- Digiloader1 file was killed by virus

3- The update file is not complete

Useful tips:

Try to use Windows XP operating system below:

http://www.chinaautodiag.com/html/ghost-windows-xp-professional-sp3-free-download-and-installation-6476.html

Note:

1- operating system here is only for digiprog 3 at obdii365.com. 

2- disable anti-virus program, otherwise, the Digiloader file would be killed by virus.

Digiprog 3 V4.94 change mileage for Chevrolet Trailblazer

Here is the customer solution to Chevrolet Trailblazer 2002 KM change with Digiprog 3 v4.94 odometer correction tool.

Many thanks to a well-known member in GMT nation forum who achieved this.

Digiprog3 and ST 01/2 cable used is China clone.

The entire kit cost $169, with a set of cables and adapters. But i don’t think everyone should buy the entire kit, for the main unit should come with ST01, ST04 cables, which will save $40. Of course you should use st01/ st04 or have other adapters in hand.

And the model to chang mileage:

Chevrolet Trailblazer LTZ 2002

And here is some useful pictures for the same process:

And here is the final result
Before mileage correction

After mileage correction with Digiprog3 V4.94

And here is some notes for doing this properly :-

• For US users, please make sure to check the Voltage of the adapter before connecting to AC (use the one included with the unit as it’s 110-220 V ). Just to make sure you don’t fry your Digiprog iii programmer
• Also for US users, Change the netric unit from KM to MPG or Vise Versa from MPG to KM; for European users, before reading or Writing on the Chip
• Very Very important to connect the programmer clip as per the pictures attached where the Red Color pin in the Clip is Up (See the picture above)
• Before assembling the cluster back together connect it to the car first and check the mileage reading before installing needles back and installing the whole cluster back to the car
• Also Very Very Very Important that you always save the old chip data in the DP3 programmer for any thing goes wrong so you can write it back if needed or even if someone fried his chip and needed to install new chip it will be really easy to write it back
• if you needed any time to restart again or your Digiprog got stuck while working simply take out the Power plug and reinsert it again to restart the programmer (Never ever unplug AC power Plug when odometer correction tool is reading or Writing on the EEPROM CHIP otherwise you will destroy it)

If you are interested, check the small video operation he made here.

http://blog.obdii365.com/2016/04/12/digiprog-3-v4-94-change-mileage-on-trailblazer-2002/