Ford Expedition 2003 mileage change with Digiprog 3

Has anyone used the Digiprog 3 v4.94 on a 2003 Ford Expedition? I'm not sure what cable to use or the correct connection points.


Solution:

Several boards were in those clusters Digiprog iii will work most of them were hc912 mcus.
Digiprog will do them whether your writing them manually by hand or with another calc built into digi
if its a hc11 it will also work


Ford Expedition 2013 dash pictures attached:

 the processor in that board is a hc912d60 mcu board

and according to tachosoft these are the mileage blocks

Car type: Ford Expedition - 68HC912D60 - 2003 year
The mileage is stored in the next lines:
0340: 4A 38 xx xx xx xx xx xx xx xx xx xx xx xx xx xx
0350: 4A 38 xx xx xx xx xx xx xx xx xx xx xx xx xx xx
0360: 4A 38 xx xx xx xx xx xx xx xx xx xx xx xx xx xx
0370: 4A 38 xx xx xx xx xx xx xx xx xx xx xx xx xx xx
0380: 4A 38 xx xx xx xx xx xx xx xx xx xx xx xx xx xx
where the next bytes:
4A 38 - is a mileage

Try this connection.

yes thats what you needed for wiring under digiprog3
goto eeprom
then page down to mcu
then select 9s12 and 9s12 4k
i believe its the 4k you need for d60
use ST48 which is 5volt St51 is 12volt when powering board instead of just mcu

wire how clusters pic is which is your life saver knowing where to grab reset on board
then handwrite mileage block

or make your life alot easier and order a usaprog or datasmart dsp3 something else
but digiprog will do as well.

www.obdii365.com

Can digiprog 3 change mileage on BMW F10?

Question:

I will buy an 2012 f10 BMW and i would like to know if its possible to change the mileage on it with my digiprog 3 v4.94 odometer master?

Actually for me it would be enough if only the dash and maybe the cas would show the mileage, the rest i don't care for the time the car will be mine. 

I have not seen the car on the digiprog list? But i have seen it on the digimaster 3 list with something online? Can someone explain it to me how it would work?




Answer:
It is impossible to do this dash via obd. you need special programmer (i.e digimaster iii) to erase the chip before writing new km, if it don't work, then have to replace chip



Digiprog3 will do miles in dash if you have a tool to erase 35160 first as for cas you will need good tool it will have 5m48h micro or you can put blocker in cluster.

digiprog3 v4.94 vehicle list

http://www.obdii365.com/upload/pro/201501/v494-digiprog-3-vehicle-list-obd365.pdf

Digiprog 3 v4.94 “Disk index out of bounds” error solution

Here is the solution on how to solve Digiprog 3 v4.94 Odometer correction Master update software “Disk index out of bounds”.

Digiprog 3 v4.94 update software error message:

Digiloader1.exe: Disk index out of bounds

Possible reasons:

1- WinXP is not compatible with the digiprog3 4.94 update software

2- Digiloader1 file was killed by virus

3- The update file is not complete

Useful tips:

Try to use Windows XP operating system below:

http://www.chinaautodiag.com/html/ghost-windows-xp-professional-sp3-free-download-and-installation-6476.html

Note:

1- operating system here is only for digiprog 3 at obdii365.com. 

2- disable anti-virus program, otherwise, the Digiloader file would be killed by virus.

Digiprog 3 V4.94 change mileage for Chevrolet Trailblazer

Here is the customer solution to Chevrolet Trailblazer 2002 KM change with Digiprog 3 v4.94 odometer correction tool.

Many thanks to a well-known member in GMT nation forum who achieved this.

Digiprog3 and ST 01/2 cable used is China clone.

The entire kit cost $169, with a set of cables and adapters. But i don’t think everyone should buy the entire kit, for the main unit should come with ST01, ST04 cables, which will save $40. Of course you should use st01/ st04 or have other adapters in hand.

And the model to chang mileage:

Chevrolet Trailblazer LTZ 2002

And here is some useful pictures for the same process:

And here is the final result
Before mileage correction

After mileage correction with Digiprog3 V4.94

And here is some notes for doing this properly :-

• For US users, please make sure to check the Voltage of the adapter before connecting to AC (use the one included with the unit as it’s 110-220 V ). Just to make sure you don’t fry your Digiprog iii programmer
• Also for US users, Change the netric unit from KM to MPG or Vise Versa from MPG to KM; for European users, before reading or Writing on the Chip
• Very Very important to connect the programmer clip as per the pictures attached where the Red Color pin in the Clip is Up (See the picture above)
• Before assembling the cluster back together connect it to the car first and check the mileage reading before installing needles back and installing the whole cluster back to the car
• Also Very Very Very Important that you always save the old chip data in the DP3 programmer for any thing goes wrong so you can write it back if needed or even if someone fried his chip and needed to install new chip it will be really easy to write it back
• if you needed any time to restart again or your Digiprog got stuck while working simply take out the Power plug and reinsert it again to restart the programmer (Never ever unplug AC power Plug when odometer correction tool is reading or Writing on the EEPROM CHIP otherwise you will destroy it)

If you are interested, check the small video operation he made here.

http://blog.obdii365.com/2016/04/12/digiprog-3-v4-94-change-mileage-on-trailblazer-2002/

Digiprog 3 V4.94 update error "List index out of bounds"

I bought Digiprog 3 v4.94 update software and followed the instruction to update my digiprog3 on WinXP laptop. But when run Digiloader1.exe file, the windows reports an error "List index out of bounds (-1)" (error screens taken below)

3 possible reasons:

1.You did not disable anti-virus program. Digiloader file was killed by virus.

2.His WinXP is not compatible with the digiprog3 4.94 update software. 

3. The update file is not complete. 

Solution:
Contact your dealer to check if your problem came with files,if yes,ask them to re-send the update file.

http://digiprog3digiprogiii.blogspot.com/2015/12/how-to-update-digiprog3-in-10-steps.html