Ford F350 odometer correction digiprog 3 pinout

I need help with a 2004 Ford F350 super duty cluster mileage correction. I’m using digiprog 3 v4.94 but i don’t have the diagram or what chip looking for to extract the info from this cluster. So I searched and find some documents.

Here is the Ford F350 digiprog III pinout on the manual book:

What is needed plug 51.
FORD VAN F350
Remove the cluster and it.
Connect shown in the photo’s below the plug 51 with the
marked soldering points. The white marked soldering points among themselves
and connect to the white wire from St. 51st (Photos s. Next page)
Select the program: cars / trucks – FORD – F350.
The DIGIPROG denotes old / incorrect Mileage.
program and completed the new / correct Mileage.

But my cluster looks different from the pic in the manual, here is mine.

Then a DigiProg expert pointed me the proper solution.

Use the BDM points mate 4 wires

Do like in clusters picture. use connector ST48 and wire to the 6 pin point pad and read thru ford f350 or thru eeprom programmer set to mcu 912 4k.

Digiprog3 v4.94 ST51 is only for 12 volt if you going to power entire board for f350 should be using st48 which gives 5volt 12volt to a mcu and youll be smoking in no time.

http://obd365.edublogs.org/2016/03/26/ford-f350-van-mileage-correction-with-digiprog-3/

Digiprog 3 DigiProg III "ERROR NO CONNECTION" solution

Hi,

I have been using Digiprog 3 v4.94 mileage programmer from obdii365.com for several months. The tool used to work well. But today, when I tried to use it to correct mileage for an Audi A4 of the year 2000, a window popped up, saying “ERROR NO CONNECTION”. I have also tested it on another A4 of the year 2006, and the error message showed up again. What could be the problem? Is the tool broken? Below is a photo of the problem. Please help. Urgently. Thanks.

David

————————————————————————————–

Dear David,

According to the error message you provide, I guess you are connecting the tool via OBD2 port, right? However, according to Digiprog3 odometer correction tool manual book, to program mileage for most cars before 2008, you will have to disassemble the dashboard and get access to the mileage chip. Then you will need to use ST01, ST04 or other cables rather than OBD2 cable to clip the chip and let the chip communicate with the DP3.

The Digiprog iii will tell you if you need to disassemble the dashboard, as well as which cable you should use to do mileage programming for the car.

Solution: You can disconnect the tool, connect it to your car again, and pay attention to system prompts to determine how to do the programming.

Best regards

Digiprog 3 odometer correction tool Access denied solution

I have tested digiprog3 v4.94 odometer correction tool on Opel Astra 2013 and Audi A8L 2007. 

DigiProg3 Prompt to Plug 16 connectors

So I connect the ST16 OBD II Diagnostic connector

My car running Old 98129 miles

After manually enter the new mileage, the DigiProg 3 display an error message ACCESS DENIED

Actually 98000 miles

 

Then I have test some other models Chevrolet Cruze 

VW Polo 2010 all via OBD way, still not luck to get them well communicated.

EEPROM changed

Was 25160 became 24s16.

24s16 changed at 95160,

Digiprog3 v4.94 change Isuzu D-Max odometer

Recently a obdii365.com customer has successfully programmed his Isuzu D-MAX odometer with Digiprog 3 Digiprog III odometer correction tool. Below are some pictures he shared us about how he did the job:

Digiprog3 V4.94

http://www.obdii365.com/wholesale/low-cost-digiprog-iii-odometer-master-programmer-entire-kit.html

Digiprog 3 V4.94 Change KM on Toyota Hilux 93c66

Obdii365.com engineers today tested Digiprog 3 v4.94 odometer correction tool on Toyota hilux 93c66. Here displays the test procedure.

Tool used: Digiprog3 v4.94 odometer programmer

Model: Toyota HILUX C66

Procedure of odometer correction with Digiprog 3 master:

Adapter connection:

Pin out connection:

TOYOTA

SELECCIONE MODELO

HILUX C66

EEPROM: 93SC66

VIEJO: 132005KM

COMPRUEBE VALOR ESCRITO – 61132KM

Mileage is changed successfully, from 132005KM to 61132KM.

NOTE: Tips for Using Digiprog III:

1. Always connect the Eeprom to the ST01 or ST04 before you connect to the DigiProg this will avoid Electro static feedback (ESD).
2. Never solder the connections whilst the lead is connected to the programmer, this will damage the DigiProg.
3. Always keep your DigiProg 3 in its case when not in Use & keep it in a dry environment at night (don’t leave it in the trunk of your car) If you are using solvents to remove lacquers’ from Eeprom’s ensure that they are cleaned
4. completely as the solvent can damage the clips.

http://blog.obdii365.com/2016/01/24/digiprog-3-v4-94-change-km-on-toyota-hilux-93c66/

Digiprog 3 V4.94 odometer correction worked and failed models

Digiprog 3 V4.94 clone has come into the market for some some. Here obdii365.com lists most of vehicles tested ok or not, by .

OBDII365 NOTE: tests below not all did by obd365 technicians, some by Digiprog 3 users at obdii365.com.

Digiprog III 4.94 successful test

1)For VW, Audi, Skoda vehicles:

Passat 2007 —> OBD OK
passat 2011 work obd 5 min
passat 2012 work obd
passat cc 2012 work obd
Passat 2011 menu dash diag -2012 read ok/write ok /3 minute.
passat 2006 dash work
passat 2011 work by OBD

Tiguan 2007 —> OBD OK
tiguan 2009: ok test Many Time always ok
Tiguan 2011 OBD no problem, takes about 10 minutes

Jetta 2013 take golf 6 on car list. Work fine 2 minutes
jetta 2012 work obd
jetta 2014: ok test Many Time always ok

Skoda Superb (3t) II 2009y only by obd less then 5min
Skoda Roomster 2009 —> Diag work Perfect
Skoda octavia 2009 1.9tdi instrument ok, ecu ok, dsg reset ok
SKODA Fabia 2009 obd ok. fabia -diag-read ?-write ok. (digi4.94)
skoda superb 2011 nec+24c64 obd works fine.

audi a4 2010 obd ok, audi a3 2010 obd ok
A6, 2009 work OBD, 4-5 minute.
no problem with audi a3 for now 2011 and 2010 doing ok by obd

Volkswagen Eos obd2 ——ok
vw eos 2007 —> Diag obd2 work

Golf 6 2012 obd ok
golf 2007: dash and dsg ok
golf mk5..ok
Golf 4 MM Just open dash en look voor 24C** it takes 2 minutes

300 m 2009 ok
wrangler 2012 ok
VW evoque 2012 work by OBD
Seat MII 2013 —> OBD Work

2)For BMW vehicles:
BMW E46 2004 —> 35080 Clip Work

3)For Ford vehicles:
Ford Fiesta 2012 —> OBD OK
Ford Fiesta HCS12 —> ST48 Work
2012 Ford Focus – 95320 – by ST1 work ok

4)For Mitsubishi:
For read & write correct Mileage use
Mitsubishi Outlander 93C86 V2 —> Work Perfect on Peugeot 4007 2012

5)For Mercedes Benz:
w211 2005 dash via st60 read ok/write ok/ezs sync blocked ok.
E39 m5 dash done with digi using st47
MERCEDES w210 E – DB 4_99 with Stecker 10 , ok!

6)For Opel:
-Opel Vivaro 2013 —> EEPROM Clip work 93c76
-Astra J 2011 work by OBD.
-Opel Insignia 2014 —> OBD Work perfect

7)For Fiat:
Fiat Grande Punto EVO 2011 dash– obd OK…. fiat doblo
Fiat Ducato 2012 work perfect OBD
Fiat Doblo 2009 —> OBD Work perfect 1 sec. Job

8)Other models:

Galaxy 2008 new model by the OBD ok
Successfully made chevrolet orlando like a opel insignia

Digiprog read/write 35080 for 100%.

Range Rover Evoque 2013 via obd ok

Nissans: 2002 Altima 93C66 OK in circuit with Murano; 2001 Xterra 93c56 OK unsolder with Patrol

Toyota RAV 4 2007 —> eeprom clip 93c56 work

– Made : sportage 2012
Swift 2014
Ranger 2010
Prado 2006
Runner 2006
Navarra 2012

All eeprom on board …i did NOT try obd
– salvage Yard
nitro 2009 ok
patriot 2013 ok
2015 xtrail does work with digiprog 4.94, chip 93c86 worked a treat
volvo s80 2008+ work good 10min.

Digiprog3 V4.94 cannot work on some
Digi can not do some Golf 6 and Polo Dash by obd.
Digi can do only VDO dash Golf 6 by obd, not Magneti Marelli.
A3 sportback 2009. killed
Focus 2011 not work

Digiprog 3 boot with flash screen (solved)

Digiprog3 v4.94 odometer correction tool power on with flashing screen solution is provided.
Problem:
One of the customers purchased the digiprog 3 mileage correction tool from aliexpress but when he powered up the device, the device kept flashing, here is the photo screen he token.

Solution:

Please contact obdii365 customer service to send you these two chips of digiprog iii (marked red picture below) for free and replace the two chips. It will work.