Confirm! It worked fine!
VW Golf 6: OBD – OK
VW Golf 5: OBD – OK
VW Golf 4: OBD – OK
VW Golf 3: OBD – OK
in detail...
Part 1: Digiprog 3 Golf 6
Golf 6 2012: done by OBD – OK
Golf 6 2011: i can change odometer with digiprog 3
china clone via OBD
But it also depends on quality of
your clone too..
Golf 6 2011: VDO tacho obd 2 min !!ok!!
Golf 6 2011: ok through OBD
Golf 6 2011: read/write ok in 5min
Golf 6 2011: not work with Nec 24c64
Golf 6 2011: Dash MM read old value ok and write ok, But dash now say: Error
and not show value
Try different value and double check
which version of dash is
Yes, this car work without dash
Golf 6 2011 MM5: obd ok
Golf 6 m.m 2011: done by obd in 5 minutes,work
VW golf 6 2010: OBD OK
Golf 6 2009: change km no issues via OBD
VW Golf mk6 2009: OBD is good with error clearing
Golf 6 2009: convertible OBD – OK
Part 2: Digiprog3 Golf 5
Golf 5: ecu
works diag
Golf 5 2008: ok through OBD
VW golf 5 2008: OBD OK
GOLF 5 2008 kombiistrument 3HL: OBD -OK 1min
GOLF 5 2008 ECU DIAG R4 1,9L EDC 000SG: OBD-ok 10min
Golf 5 2007: ODO AND ECU EDC16 ok
VW golf 5 2007: OBD tacho OK, ecu OBD OK
Golf 5 2005 2006 2007: OBD change km
Golf 5 2006 1,9 tdi: obd OK
Golf 5 2006: odo and ecu OK
VW golf 5 2003: OBD no connection
Golf 5 edc16: all ok
Golf 5:
obd ok
VW Golf MK5 2.0 TDI 140cv DSG BKD Engine:
Dash kms : OK
DSG kms: OK
ECU Diag: Unknown version, not read
Service: OK
Golf 5 Dash Visteon 95160: less than a minute OK
Golf 5 ECU EDC16: 6~8 minutes OK
Golf mk 5 2006: ok through OBD
VW Golf mk5 2006: dash+ edc16 OBD is good
Part 3: Digiprog 3 Golf 4 Golf 3:
Golf 3 & Golf 4: works OK via dash connector and via OBD
Golf 4 19tdi 2000: change mileage OK
Golf mk4: obd ok
VW golf 4 2004 tdi: OBD OK
VW golf 4 2002: bosch OBD OK
Golf 4:
vdo ok edc 15 not work
Part 4: Digiprog 3 old version 4.88 and Golf
Digiprog 3 v4.88: worked
I have china clone version 4.88 and
it worked fine.
Digiprog 3 v4.88: worked
I use always my DP3 4.88 with many
golf 6 and no problem !
Digiprog 3 v4.88: not worked
My DP3 v4.88 damaged the eeprom
content, and
apart from not changing km, the
backlight is always on
Digiprog 3 v4.88: not worked
DP3 v4.88 does not work with MM5 dash
(NEC mcu)
Tested on Golf variant 2010 and 2011
IMPORTANT TIP:
You’d better have Digiprog 3 v4.94
for odometer correction.
It works for more cars than v4.84.
Look here: Digiprog 3 4.94 on Golf 5 odometer correction
Tech support from obdii365.com
No comments:
Post a Comment
Note: Only a member of this blog may post a comment.